Skip to content

Steps & Staircases

Resin Bound Steps & Staircases in Brentwood

A close-textured, slip-resistant finish that holds its edge through daily foot traffic and wet weather.

  • Itemised Quote
  • Base Assessed First
  • 1-3mm Aggregate
Front entrance of a traditional stone house with a dark wooden door, resin-bound steps and pathway, and decorative landscaping with lavender and hydrangeas.

What Goes Wrong

Where rushed resin step work fails, and how to avoid it

Hollow Base

A resin layer applied over a hollow or cracked substrate will delaminate under repeated foot traffic within months.

Base Integrity Check

Each step is tapped and inspected for voids before any material is mixed or laid.

Unfinished Nosing

Step edges left without defined edge detailing chip away quickly, leaving a rough, unsafe tread corner.

Defined Edge Detail

The nosing is finished with a clean, set edge profile to resist chipping under foot traffic.

Wrong Aggregate Size

A coarse aggregate on steps creates an uneven tread that catches shoe soles and wears unevenly over time.

1-3mm Blend Specified

A fine 1-3mm aggregate produces a close, even texture that grips underfoot without snagging.

Poor Drainage

Water pooling on treads accelerates surface degradation and makes steps hazardous in wet conditions.

Drainage Assessed

Falls and drainage are checked at survey stage so water runs clear of the treads after laying.

Scope of Work

What resin bound step resurfacing covers

From a single front entrance step to a full garden staircase, the scope is assessed and quoted in full before work starts.

Front Entrance Steps

Single or multi-step front door approaches.

Garden Staircases

Sloped garden access steps resurfaced in resin.

Side Access Steps

Utility and side-return step resurfacing.

Step Repairs Before Laying

Crack filling and void repair prior to resin.

Steps & Staircases

Resurfacing outdoor steps safely with resin bound aggregate

Worn or slippery steps need a surface that grips underfoot and holds its edge through heavy use.

Start Your Enquiry

Outdoor steps take more concentrated wear than flat surfaces. The tread edge, the nosing, is the first area to chip or delaminate if the base beneath is hollow or the resin layer is applied without proper edge detailing. Many older properties around Brentwood have original concrete or brick front steps where the surface has worn smooth and become difficult to clean. Before any resin is applied, each step is checked for base integrity, drainage, and level.

Surface preparation involves cleaning the existing tread and riser, filling any cracks or voids, and applying a bonding primer. The resin bound layer, aggregate mixed into UV-stable polyurethane resin, is then trowelled across the tread and down the riser face. Nosing edges are finished with a defined edge detail to prevent chipping under foot traffic. The aggregate blend is selected to match or complement an adjacent resin driveway or path where visual continuity matters.

Slip resistance is determined by aggregate size and surface texture. A finer aggregate produces a closer-textured surface that grips underfoot even when wet, relevant for front entrance steps that are exposed to rain year-round. The finished surface is assessed against the surrounding drainage to ensure water runs off the treads rather than sitting on them. Cure time is typically 24 hours before the steps are returned to use.

Why Choose Us

Why choose us for resin bound steps in Brentwood?

Steps are a safety-critical surface. The assurance behind the work matters as much as the finish itself.

Itemised Quotation Every Time

Preparation, materials, edge detailing, and finishing are quoted as separate lines, no single combined figure.

Base Assessed Before Pricing

A local resin specialist surveys the existing steps before any price is given, so the quote reflects actual site conditions.

Vetted Local Partners

Enquiries are connected to vetted independent local partners who work on Brentwood properties regularly.

No Hidden Repair Costs

If crack filling or void repair is needed before laying, that work is quoted as a separate line, not absorbed silently.

Aggregate Matched to Adjacent Surfaces

The blend is chosen at survey stage to tie the steps visually to any existing resin surface on the property.

A newly installed grey resin-bound driveway with a central decorative pattern leads to a modern double garage.
A modern brick house with a newly installed dark grey resin driveway, landscaped front garden, and an oak timber porch.

How It Works

From enquiry to finished steps in three stages

Start Your Enquiry

  1. 01

    Describe Your Steps

    Tell us the number of steps, what they are made of now, and whether any are cracked or draining poorly.

  2. 02

    Survey & Quote

    A local resin specialist visits to assess the base, drainage, and nosing condition, then provides an itemised quote.

  3. 03

    Prepare, Lay & Cure

    The steps are prepared, primed, and finished in resin bound aggregate, ready to use within 24 hours of laying.

Pricing Estimates

Typical Resin Bound Steps & Staircases Prices

JobTypical cost
Simple step repair£300-£600
Small step set£600-£1,200
Full staircase finish£1,200-£2,500
Detailed or awkward staircase£2,500-£4,000
These prices are estimates and often vary with the condition, size and scope of each job. Message or call us for a free, no-obligation quote.
See all prices

Common Questions

Questions about resin bound steps

  • Can resin-bound surfacing be used on outdoor steps?

    Yes, when the base is sound and properly prepared. The existing steps need to be stable, level enough, and detailed correctly at the edges. A survey confirms whether the current surface is suitable or needs repair work first.

  • Are resin steps slippery when wet?

    A correctly specified resin bound surface uses a fine aggregate, typically 1-3mm, that produces a close-textured tread. This grips underfoot in wet conditions. The aggregate size and blend are chosen at survey stage with outdoor use in mind.

  • Do the old steps need to be removed first?

    Not always. If the existing steps are structurally sound, resin can be applied as an overlay after preparation. Badly cracked, hollow, or moving steps may need repair or rebuilding before the resin layer can be fitted properly.

  • What happens if I delay resurfacing worn or slippery steps?

    A worn, smooth surface becomes more hazardous in wet weather. Cracks also allow water to penetrate the base, which accelerates deterioration and can mean more extensive repair work, and higher cost, by the time resurfacing is carried out.

  • Can the steps be matched to an existing resin driveway or path?

    Yes. The aggregate blend and colour are selected at survey stage to complement or match an adjacent resin surface. Many Brentwood properties with resin driveways choose this approach to give the whole front entrance a consistent finish.

More questions about Resin Bound Steps & Staircases?

Get Slip-Resistant Steps That Last

Describe your steps and we’ll arrange a local resin specialist to assess the base and provide an itemised quote, preparation, materials, and edge detailing as separate lines.

Start Your Enquiry